PRODUCT產品介紹
SP35 Mini-Storage
Introduction
SP35 Mini-Storage Series combine features of instant and storage types, which enables instant heat-up and storage of hot water. It is best suit for small family or group of 2-4 people.
Won "Taiwan Excellence Award".
Trendy appearance.
High level waterproof.
Three installation methods-vertical wall, horizontal wall, and horizontal ceiling.
Standard factory temperature setting at 65°C.
Capable of providing 40°C of hot water up to 100 liters.
Hidden installation inside ceiling is available for saving ground space.
Quality 304 stainless steel inner design, construction plastic material cover.
Indicating light clearly shows power status: ON-heating or OFF-keep warm.
Special inner tank design for instant heating that provides continuous hot water.
Thickness of above 3.8cm flame-retardant insulation layer enables good warmth-keeping.
Unique heating element design that increases heat convection scope, which allow evenly heat-up of water thus able to provide sufficient hot water.
Safety devices including pressure relief valve and check valve, leakage circuit breaker, auto cut-off of power supply device upon abnormal situation and further stage of protection from unusual high temperature drained heating.
Won "Taiwan Excellence Award".
Trendy appearance.
High level waterproof.
Three installation methods-vertical wall, horizontal wall, and horizontal ceiling.
Standard factory temperature setting at 65°C.
Capable of providing 40°C of hot water up to 100 liters.
Hidden installation inside ceiling is available for saving ground space.
Quality 304 stainless steel inner design, construction plastic material cover.
Indicating light clearly shows power status: ON-heating or OFF-keep warm.
Special inner tank design for instant heating that provides continuous hot water.
Thickness of above 3.8cm flame-retardant insulation layer enables good warmth-keeping.
Unique heating element design that increases heat convection scope, which allow evenly heat-up of water thus able to provide sufficient hot water.
Safety devices including pressure relief valve and check valve, leakage circuit breaker, auto cut-off of power supply device upon abnormal situation and further stage of protection from unusual high temperature drained heating.
-
Vertical wall-mounted
MODEL Capacity Voltage Current Power Phase Water Connection Time to increase
by 25°CDimensions SP35 7.5 gallons (28 llters) 220V 27A 6kW Single 1/2” 8 mins 70(L)x42(W)x39(D)cm
Horizontal wall-mountedMODEL Capacity Voltage Current Power Phase Water Connection Time to increase
by 25°CDimensions SP35 7.5 gallons (28 llters) 220V 27A 6kW Single 1/2” 8 mins 42(L)x70(W)x39(D)cm
Horizontal ceiling-mountedMODEL Capacity Voltage Current Power Phase Water Connection Time to increase
by 25°CDimensions SP35 7.5 gallons (28 llters) 220V 27A 6kW Single 1/2” 8 mins 42(L)x70(W)x39(D)cm
-
-
Installation – Mini Storage Electric Water Heater
- Install as close to faucet as possible to prevent heat lost in pipe.
- Ensuring the tripod or wall-mounted hook is tight when installing.
Water Connection- Connect safety valve to cold water inlet. Connect pressure releasing pipeon pressure releasing hole of the safety valve can avoid danger cause by pressure releasing.
- Note that the pressure releasing hole should never be blocked.
- Keep the cold water inlet faucet open, it is normal if safety valve drips during heating.
- Inlet water pressure is recommended to remain under 1kgf / cm². However, highly recommended to install pressure decreasing valve when pressure exceed 2kgf / cm².
- Inlet and outlet connection gauge should be the same according to the product specification.
- Install safety valve is necessary ensuring the safety.
Power Connection- Power cord is either black or red. Make sure to connect the green earth cord correctly.
- Note that the blue dot inlet pipe indicates cold water inlet pipe whereas red dot indicates hot water outlet, make sure installation is correct.
-
Reminder – Mini-Storage SP35
- All electrical installation should be carried out by a qualified person. Make sure the operation of Power and water supply before contact the distributor.
- Electrical Regulation Replacement
- Please switch off the power and take off the terminal of the electrical regulation and all wires before replacing the electrical regulation. Ensuring the screw and nut are tighten after replacement and wires arrangement.
- Heating element function
- Water (faucet) should be leaked off (switch-off) before replacement of heating element function. Once installation completes, turn on both hot water faucet and cold water faucet then open the clean access.
- Heating element function is able to be taken apart by wrench. Ensuring the rubber washer is well fixed preventing the water heater from leaking before re-arranging the heating element function.
- Scheduled Maintenance
- Heating system should be cleaned once two year ensuring the heating quality which is highly recommend.
- Scheduled cleaning the exterior of water heater to keep intact.
- 1 year warranty for the product.
- Overheat Preventive Device will automatically interrupt by abnormal overheating.
- Attention: Turn off the power immediately while power indicator not illuminating and contact customer service.
-